Platform P360 – Universal Substrate Alkali Resistant Primer 1 Gal

$64.75

(well bonded, clean, dry, sound and stable)

  • Concrete – absorbent and non-absorbent
  • Gypsum
  • Wood
  • VCT
  • Ceramic tile
  • Cement terrazzo
  • Cutback adhesive residue
  • Epoxy moisture vapor membranes (free from amine blush)
  • Other approved substrates

Surface Preparation

All surfaces must be sound, stable, and clean. Ensure surfaces are free from dust and dirt and any bond breaking materials (silicates, curing compounds, oils). Mechanically remove weak surfaces and any contaminants to sound surface. Always finish cleaning by a final removal of contaminants by vacuum. Not for use over water soluble adhesives or pressure sensitive adhesives. In those cases, remove adhesive prior to priming.

Application Procedures

FOR PROFESSIONAL USE ONLY

Use chemical resistant gloves when handling.

Mixing

To address any settling, mix P360 briefly with a low speed (300 rpm) mixer and paint paddle to ensure all contents are homogenous (typically 30 seconds). Use full strength as directed. When specific substrates require the dilution of P360, mix again after diluted to the desired ratio with low speed mixer (typically 1 min). Remix diluted material if it sits more than 24 hours.

Material Application

Substrates can be tested for absorbency onsite. Place a bottle-capful of clean water on the substrate, if it readily disappears into the substrate, substrate is absorbent.

Absorbent Substrates

(Typically concrete, gypsum); Dilute Primer 3:1 (water:primer).
Ensure the substrate stays wet for at least 15 minutes. Substrates that “flash dry” may require additional dilution, or other remedial actions. If substrate does not stay wet at least 15 minutes, contact Platform Technical Support. Gypsum substrates tend to be very absorbent and may require additional dilution. In many cases gypsum requires primer dilution of 6:1 (water:primer or even 10:1 to maintain desired wet surface for 15 minutes).

Once diluted use a push broom with fine tips and spread P360 with the broom working it back and forth across the surface to ensure penetration into the pours of the substrate. Avoid allowing the material to puddle, rather spread any puddles uniformly across the surface. Some highly porous surfaces may require an additional primer coat (primer effectiveness can be water tested with a capful of water after it has dried).

Non-Absorbent Substrates

(VCT, Adhesive Residues, Cement Terrazzo, Moisture Membranes, Epoxy). Apply undiluted P360 with a paint or dual cage roller using a 3/8” nap roller. Spread to ensure the entire surface is covered with a thin, even film, avoiding puddling. If material puddles, spread uniformly across substrate. Not for use over water soluble adhesives or pressure sensitive adhesives. In those cases, remove adhesive prior to priming.

Double prime all wood substrates with P360 NEAT. Spread to ensure the entire surface is covered with a thin, even film, avoiding puddling. If material puddles, spread uniformly across substrate. Ensure the first coat of primer dries completely prior to installing the second coat of primer.

Dry Time

Ambient conditions (temperature, humidity, air movement) will impact dry time. Universal Primer typically dries in 45 minutes to 90 minutes. Roll out to a uniform film with no ridges or primer build. Areas must be re-primed if more than 48 hours passes since Primer P360 application, or in the case of contamination by dust or foreign material.

95 in stock

SKU: 000183 Category:

Maximum versatility for market leading bond strength on both porous (eg. concrete) and non-porous (eg. epoxy) substrates. Fast drying P360 formula allows application of self-leveling underlayment in 45 – 90 minutes. High solids permits regular dilutions of 3:1 (water:primer) providing exceptional coverage rates of 800 – 1200 sq ft. per gallon.

New technology polymer is entirely resistant to environments of pH 14 for extended periods of time.

One primer, superior outcomes.

FEATURES
  • Fast drying
  • Maximum versatility for porous and non-porous substrates
  • Exceptional bond performance
  • Prolonged resistance to pH 14
  • Excellent coverage
  • Low odor and low-VOC

Reviews

There are no reviews yet.

Be the first to review “Platform P360 – Universal Substrate Alkali Resistant Primer 1 Gal”

Your email address will not be published. Required fields are marked *

0
    0
    Your Cart
    Your cart is emptyReturn to Shop